Search Samsung

Looking for Answers about samsung RMC-QTD1?

Choose a Category
AppstoreApps(Q:636 A:259)
Battery(Q:1 A:0)
Chargers(Q:2 A:2)
Dishwashers(Q:16 A:25)
Dryers(Q:44 A:55)
Electric Ranges(Q:85 A:112)
French Door(Q:3 A:4)
Gas Ranges(Q:98 A:126)
Induction(Q:6 A:9)
LED Lighting(Q:2 A:3)
OTR(Q:117 A:171)
Pedestals(Q:8 A:7)
Side Vent Kit(Q:6 A:5)
Top Load Washers(Q:41 A:74)
UHD TV(Q:64 A:56)
Verizon Wireless(Q:109 A:125)
Washers(Q:25 A:37)
Water Filters(Q:14 A:14)
Shop now at Samsung
or
Choose a Category

Customer Questions & Answers for
RMC-QTD1

Customer Questions & Answers:
160 Questions
 | 
67 Answers

Questions & Answers for samsung RMC-QTD1

Question

When tryign to pair the qwerty remote to my 2011 8000 series tv the remote says BT ERROR and will not reset.

asked 3 years, 5 months ago
raptured11
on RMC-QTD1
0points
0out of 0found this question helpful.
0 answers
Answers
This question currently has no approved answers.
Question

how do i pair my remote?

everytime i try to pair my remote it says "failure to pair". what do i do?
asked 2 years, 10 months ago
patj4041
tulsa, ok
on RMC-QTD1
0points
0out of 0found this question helpful.
4 answers
Answers
answer 1
The secret is to move in close to the TV - about 10" or so - to get the proper pairing signal.
answered 2 years, 8 months ago
kevena
0points
0out of 0found this answer helpful.
answer 2
Press the @ and backspace button to reset the remote and try again.
answered 2 years, 9 months ago
HVRZ5uShooter
Los Angeles
+1point
1out of 1found this answer helpful.
answer 3
Clear the remote by pressing @ and the backspace arrow. The, pair again.
answered 2 years, 9 months ago
HVRZ5uShooter
Los Angeles
0points
0out of 0found this answer helpful.
answer 4
I was having trouble setting up my QWERTY Remote RMC-QTD1, but only managed to set up control after that I was close to the TV
The tip is set close to the TV!
answered 2 years, 9 months ago
MarceloK
Brazil
0points
0out of 0found this answer helpful.
Question

Pairing QWERTY Remote to TV

My new QWERTY Remote RMC-QTD1 will not pair with my LED TV UN55D6900. What is the proper procedure. The manual is not clear about this. I am pushing "SYM" and "TAB" at the same time and get a "Failure" display after about 30 sec. What gives ??
Peter.
asked 3 years, 3 months ago
PeterIngwersen
on RMC-QTD1
0points
0out of 0found this question helpful.
3 answers
Answers
answer 1
I was having trouble setting up my QWERTY Remote RMC-QTD1, but after that I followed the tip of the BraZeNisGod's, leaving close control the TV, everything worked out.
The configuration should be done near the TV.
answered 2 years, 9 months ago
MarceloK
Brazil
0points
0out of 0found this answer helpful.
answer 2
Hey Peter,
Proximity is key for pairing. Make sure you are only 5-10 inches from the television while holding the SYM+TAB to start pairing. If you can pair successfully and then lose connection somehow (while still reasonably close to the television of course) you may have some local interference or a faulty BT module in the set or the remote. I would recommend calling Sammy support at that point.

Good luck, its an awesome gadget once you get it working!

-Dan
answered 2 years, 11 months ago
BraZeNisGod
Virginia
0points
0out of 0found this answer helpful.
answer 3
My new QWERTY Remote RMC-QTD1 will not pair with my LED TV UN55D6900. What is the proper procedure. The manual is not clear about this. I am pushing "SYM" and "TAB" at the same time and get a "Failure" display after about 30 sec. I also watched the youtube video on pairing. It paired for about ten minutes then quit working.
answered 3 years, 2 months ago
boligee
Birmingham
0points
0out of 0found this answer helpful.
Question

how do I register my QWERTY remote?

There are no model number picks on the registration page.
asked 3 years, 2 months ago
DaveinBoston
Boston
on RMC-QTD1
-1point
0out of 1found this question helpful.
2 answers
Answers
answer 1
it is RMC-QTD1.TV acessories and follow
answered 2 years, 9 months ago
cinek361
NY
0points
0out of 0found this answer helpful.
answer 2
Go to samsung.com/register
answered 3 years ago
Vinny1
Irvine
0points
0out of 0found this answer helpful.
Question

cant pair qwerty remote side with my samsung smart tv

asked 3 years, 2 months ago
snooze
14472
on RMC-QTD1
0points
0out of 0found this question helpful.
2 answers
Answers
answer 1
I was having trouble setting up my QWERTY Remote RMC-QTD1, but only managed to set up control after that I was close to the TV
The tip is set close to the TV!
answered 2 years, 9 months ago
MarceloK
Brazil
0points
0out of 0found this answer helpful.
answer 2
Try it right next to the TV
answered 3 years, 2 months ago
Crvtte65
0points
0out of 0found this answer helpful.
Question

Where's The Serial Number?

Need It For Registration
asked 3 years ago
xracer23
on RMC-QTD1
0points
0out of 0found this question helpful.
2 answers
Answers
answer 1
UNDER THE ACCESS PANEL TO THE BATTERIES
answered 2 years, 8 months ago
Hoppyjr
0points
0out of 0found this answer helpful.
answer 2
For the qwerty remote? It's inside the battery cover lid.
answered 3 years ago
Vinny1
Irvine
0points
0out of 0found this answer helpful.
Question

How can I get my Qwerty Remote to Pair?

asked 2 years, 11 months ago
Anonymous
on RMC-QTD1
0points
0out of 0found this question helpful.
2 answers
Answers
answer 1
stand very close.press SYM+TAB by 2 sec.
answered 2 years, 9 months ago
cinek361
NY
0points
0out of 0found this answer helpful.
answer 2
I had to stand real close to the tv then press SYM and TAB at the same time for a couple of seconds.
answered 2 years, 10 months ago
Meeklo
Wenatchee, WA
0points
0out of 0found this answer helpful.
Question

cannot pair RMC-QTD1 remote with my UN46C8000XFZA led tv

I am trying to pair the QWERTY remote with my LED TV by pressing SYM + TAB buttons, but nothing happens. It is not even giving me any errors. Is this remote even compatible with my TV? The SAMSUNG web site said it is.
asked 2 years, 9 months ago
dhruvm
USA
on RMC-QTD1
0points
0out of 0found this question helpful.
2 answers
Answers
answer 1
I was having trouble setting up my QWERTY Remote RMC-QTD1, but only managed to set up control after that I was close to the TV
The trick is to make close control of the TV!
answered 2 years, 9 months ago
MarceloK
Brazil
0points
0out of 0found this answer helpful.
answer 2
just do that so close to the TV
answered 2 years, 9 months ago
cinek361
NY
0points
0out of 0found this answer helpful.
Question

Remote will not pair

I keep pushing the sym + tab key and it goes to pairing, but when its done it says it needs to be paired.
asked 2 years, 9 months ago
kikilo13
on RMC-QTD1
0points
0out of 0found this question helpful.
2 answers
Answers
answer 1
Get within a few inches of the tv and try it again. If not, clear the remote by pushing @ and backspace buttons and then pair again.
answered 2 years, 9 months ago
HVRZ5uShooter
Los Angeles
0points
0out of 0found this answer helpful.
answer 2
I was having trouble setting up my QWERTY Remote RMC-QTD1, but only managed to set up control after that I was close to the TV
The trick is to make close control of the TV!
answered 2 years, 9 months ago
MarceloK
Brazil
0points
0out of 0found this answer helpful.
Question

How do I reset pairing?

I was getting pairing failures last night, and now I can't even get the remote to try and pair to my new Samsung TV (UN55D8000YF). How do I reset the remote? The manual says press Mute-0-Mute-0, but that didn't work. I've removed and installed the batteries with no luck. Any help would be greatly appreciated. Thanks.
asked 3 years, 6 months ago
jgraessley
on RMC-QTD1
0points
0out of 0found this question helpful.
1 answer
Answers
answer 1
http://support-us.samsung.com/cyber/popup/iframe/pop_troubleshooting_fr.jsp?idx=341001&modelname=UN46D7000LF&modelcode=&session_id=

Hold the remote within a few inches of the tv when pairing
answered 3 years, 5 months ago
RagingSamurai
0points
0out of 0found this answer helpful.
Question

HOW DO I TROUBLESHOOT THW QWETY CONTROL WHEN ONE SIDE DOES NOT RESPOND?

I CANT GET ONE SIDE TO WORK THE SIDE WITH THE KEY BOARD
asked 3 years, 6 months ago
DHFULLBACK
NEW YORK
on RMC-QTD1
0points
0out of 0found this question helpful.
1 answer
Answers
answer 1
reset the remote

http://support-us.samsung.com/cyber/popup/iframe/pop_troubleshooting_fr.jsp?idx=341001&modelname=UN46D7000LF&modelcode=&session_id=

hold the remote within a few inches when pairing
answered 3 years, 5 months ago
RagingSamurai
0points
0out of 0found this answer helpful.
Question

Cannot pair the QWERTY remote RMC-QTD1 with my new series 7000 3D LED TV

I have repeatedly tried all of the steps to pair the keyboard side of the Qwerty remote with my tv and nothing works. I have followed the instructions meticulously. I even went to the store and they replaced my remote. I have a feeling its a setting with the TV, but can't find anything to help me!!! Getting very frustrated!
asked 3 years, 6 months ago
AnimateTed
North Hollywood CA
on RMC-QTD1
0points
0out of 0found this question helpful.
1 answer
Answers
answer 1
hold the remote within a few inches of tv when pairing
answered 3 years, 5 months ago
RagingSamurai
0points
0out of 0found this answer helpful.
Question

When can I buy one at my local store?

Its been advertised for months on this website.
asked 3 years, 5 months ago
NLD3
Media, Pa
on RMC-QTD1
0points
0out of 0found this question helpful.
1 answer
Answers
answer 1
They are available through local retailer's now.
answered 3 years, 2 months ago
deffusion
0points
0out of 0found this answer helpful.
Question

Will the rmcqtd1 remote control work with the pn59d8000 tv

This remote control came with the set but I get failure message when I try to pair.
asked 3 years, 6 months ago
Really2Disappointed
Shaprsburg, GA
on RMC-QTD1
0points
0out of 0found this question helpful.
1 answer
Answers
answer 1
hold the remote within a few inches when pairing
answered 3 years, 5 months ago
RagingSamurai
0points
0out of 0found this answer helpful.
Question

My qwerty remote isnt working

I tried to pair it and it just keeps saying "failure" The other side works fine
asked 3 years, 4 months ago
burb21
Phoenix
on RMC-QTD1
0points
0out of 0found this question helpful.
1 answer
Answers
answer 1
I was having trouble setting up my QWERTY Remote RMC-QTD1, but only managed to set up control after that I was close to the TV
The tip is set close to the TV!
answered 2 years, 9 months ago
MarceloK
Brazil
0points
0out of 0found this answer helpful.
Question

un46d6420 compatibility

I was told when I bought my un46d6420, that it would work with the qwerty remote. Your site says it won't. Which is true?
asked 3 years, 4 months ago
ThunderPC
Duncan, SC
on RMC-QTD1
0points
0out of 0found this question helpful.
1 answer
Answers
answer 1
Samsung site...
answered 3 years, 3 months ago
DPCEMKER
Las Vegas
0points
0out of 0found this answer helpful.
Question

What is BT ERROR on the qwerty remote?

asked 3 years, 5 months ago
JBRooney
on RMC-QTD1
0points
0out of 0found this question helpful.
1 answer
Answers
answer 1
means blue-tooth connection error, must repair remote
answered 2 years, 10 months ago
beware1
-3points
0out of 3found this answer helpful.
Question

Can not reset my QWERTY remote so that I can pair it, have taken the batteries out, used the mute 0 thing and held it with in inches of the TV. Help.

asked 3 years, 4 months ago
CIndyRnW
Fort Worth
on RMC-QTD1
0points
0out of 0found this question helpful.
1 answer
Answers
answer 1
The answer is more then likely that your TV unit is NOT compartible with the QWERTY remote. There is no need to pair the remote with your TV unit.
answered 3 years, 3 months ago
DPCEMKER
Las Vegas
-2points
0out of 2found this answer helpful.
Question

How to use other devices (i.e. DVD Player) with the remote RMC-QTD1?

I am trying to control my dvd player using my new remote that came with my Smart TV. I can not find a manual on this remote anywhere? Please help because this is frustrating!
asked 3 years, 3 months ago
zpattern
Houston
on RMC-QTD1
0points
0out of 0found this question helpful.
1 answer
Answers
answer 1
It all depend on what TV MODELS r u using. Give more details and I would be able to help you out.
answered 3 years, 3 months ago
DPCEMKER
Las Vegas
0points
0out of 0found this answer helpful.
Question

having trouble pairing my remote to tv?

For some reason I keep getting a failure notice? Im pressing both SYM and TAB. Am i doing something wrong?
asked 3 years, 4 months ago
Cisco9980
on RMC-QTD1
0points
0out of 0found this question helpful.
1 answer
Answers
answer 1
I was having trouble setting up my QWERTY Remote RMC-QTD1, but only managed to set up control after that I was close to the TV
The tip is set close to the TV!
answered 2 years, 9 months ago
MarceloK
Brazil
-1point
0out of 1found this answer helpful.
1 2 3 4 5 ... 8 next>>
Copyright © 1995-2014 SAMSUNG All rights reserved.